STUDI EVALUASI DAN RENOVASI SISTEM PENTANAHAN DI SEKOLAH MENENGAH KEJURUAN (SMK) NEGERI 1 CIMAHI
DOI:
https://doi.org/10.53834/mdn.v7i1.3029Abstract
This research is a follow-up to the findings of the inspection and grounding testing in PKM 2018 activities. The value obtained exceeds 5 ohms. This is not according to the standards based on the General Requirements for Electrical Installation (PUIL) 2011. In the 2019 PKM program activities, evaluation and renovation studies of the installed earthing system which includes: surveying the location to be grounded, drilling for the position of the electrodes to be installed, installation of electrodes equipped with Bentonic material which functions as a binder so that the electrodes with the ground become one and strong, measurement of the earthing value, perform grounding installation, re-measurement of earthing. The earthing value obtained is much smaller than the previous measurement results of 2.83 ohms in the Electronics Laboratory and 2.72 Ohms at the Automation Laboratory of SMKN 1 Cimahi. It is according to the recommended standard PUIL 2011. The PKM team proposes the management of SMKN 1 Cimahi to carry out a routine maintenance and measurement process twice a year on the newly installed earthing system so that the earthing value remains according to the standard.References
Aris Sunawar, ‘ Analisis Pengaruh Temperatur dan Kadar Garam Terhadap Hambatan Jenis Tanah’ SETRUM – Volume 2, No. 1, Juni 2013, Universitas Negeri Jakarta.
I Wayan Sudiartha, “Analisis Pengaruh Jenis Tanah Terhadap Besarnya Nilai Tahanan Pentanahan”, Jurnal Logic Volume 16 No. 1, Maret 2016, Politeknik Negeri Bali.
Deni Setiawan, ‘Analisis Pengaruh Penambahan Garam dan Arang Sebagai Soil Treatment dalam Menurunkan Tahanan Pentanahan Variasi Kedalaman Elektroda’ Transient Jurnal ilmiah Teknik Elektro, vol. 7, no. 2, 12 September 2018, UNDIP.
SNI 04-0225-2000, “Persyaratan Umum Instalasi Listrik 2000 (PUIL 2000)” Badan Standardisasi Nasional, Jakarta 2000.
Dian Eka Putra, ‘Pengukuran Grounding SDP Panel Distribusi Instalasi Rekam Medis RSUP Dr. Mohammad Hoesin Palembang’ Jurnal Ampere, Volume 3, No.1, Juni 2018, Universitas Palembang.
Yul Martin, ‘Pengaruh Pencampuran Gypsum Sebagai Zat Aditif Untuk Penurunan Nilai Tahanan Grounding Pada Elektroda Batang Tunggal’, Seminar nasional teknik elektro 2018 Universitas lampung.
Managam Rajagukguk, ‘Penentuan Nilai Impedansi Elektroda Batang Tunggal Berdasarkan Karakteristik Response Impuls’, Jurnal ELKHA Vol 2, Vol. 2, Juli 2010, Universitas Tanjungpura Pontianak.
Makmur Saini, ‘Pengembangan Sistem Penangkal Petir dan Pentanahan Elektroda Rod dan Plat’, Journal INTEK, Volume 3, Nomor 2, 2016, Politeknik Negeri Ujung Pandang.
Achmad Budiman, ‘Analisa Tahanan Pentanahan Peralatan Gedung Laboratorium Teknik Universitas Borneo Tarakan Yang Menggunakan Elektrode Pasak Tunggal Panjang 2 Meter, Jurnal JPE, Vol. 21, No. 1, Bulan Mei, Tahun 2017-Universitas Borneo Tarakan
Achmad Budiman, “ Analisa Perbandingan Tahanan Pentanahan Peralatan Elektroda Pasak pada Gedung Teknik Universitas Borneo Tarakan “,Jurnal Nasional Teknik Elektro Vol 6, No. 3, November 2017 Universitas Borneo Tarakan.
Muhammad Suyanto, ‘Pengukuran Sistem Pentanahan pada Rumah Tinggal Sebagai Upaya Perbaikan Grounding untuk Mengurangi Efek Tegangan Sentuh’, Jurnal Teknik Vol 28 No 3 Oktober 2015 Universitas Pancasila
Thamrin Siahaan, Studi Pentanahan Peralatan dan Sistem Instalasi Listrik pada Gedung Kantor BICT PT. Pelindo I (Persero) Belawan, Jurnal Teknologi Energi, Jurnal Teknik Elektro Volume VIII, Nomor 2, September 2019
Fr1ely Didit Sukardi1, Prototipe Pengaman Peralatan Instalasi Listrik dan Tegangan Sentuh Bagi Manusia dengan ELCB ( Earth Leakege Circuit Breaker ), Jurnal Teknologi Elekterika No.2, Vol.16, 2019.
SNI 0225-2011, “Persyaratan Umum Instalasi Listrik 2011 (PUIL 2000)” Badan Standardisasi Nasional, Jakarta 2011.
Hutauruk,T.S,“Pengetanahan netral sistem tenaga & pengetanahan peralatan”, Erlangga, Jakarta, 1999
Downloads
Published
Issue
Section
License
Copyright (c) 2021 jurnal madani
This work is licensed under a Creative Commons Attribution 4.0 International License.
CC BY: This license allows reusers to distribute, remix, adapt, and build upon the material in any medium or format, so long as attribution is given to the creator. The license allows for commercial use.
