STUDI EKONOMI TEKNIK PEMBUATAN PERAHU CADIK JENIS BOTTOM GLASS DARI BAHAN FIBER GLASS UNTUK WISATA BAHARI DI KELURAHAN BANTEN KECAMATAN KASEMEN KOTA SERANG PROVINSI BANTEN

Authors

  • Sri Sulasminingsih Prodi Teknik Industri, Universitas Pembangunan Nasional “Veteran” Jakarta, Jakarta Selatan, Indonesia
  • Budiman Adi Setyawan UPN "Veteran" Jakarta
  • Amir Marasabessy UPN Veteran Jakarta

DOI:

https://doi.org/10.54378/bt.v13i2.224

Keywords:

Katir, the sea tourisme, bottom glass, BEP

Abstract

The fishermen in Kasemen subdistrict are the traditional fishermen who depend on the stars in the sky for navigation in caching fishes at the ocean . So, they do not go to the ocean everyday. There are many days that they must stay at home. They have another skill besides the fishermen. That is a problem. A solution of this problem is producing a special boat for the ocean tourisme. The boat is katir boat that made from plastics and combine with the glass at the bottom to see the beautiful under water views. The fishermen could be the guide of the sea tourisme because this area is rich with life and under water views. For the first , study to calculate of the cost is to be done , make a design of katir boat with the glass on the bottom and steps of production with economy of engineering method. The results are if the fishermen have to make the boat (Katir) with a special type by themselves need a lot of cost Rp.11.500.000 by a boat (without the engine) . If  the owner of the boats want to make of Katir production from fiberglass with a glass on the bottom as a special type for the ocean tourisme make a lot of cost Rp.12.710.000 by a boat (without the engine)  and get a Rp.1.110.000 profit  after reduced by production cost Rp.11.600.000 by a boat. If the investors want to enter the bussiness of  Katir industry seriously , the capital will be back (Break Event Point/BEP) on time of 4.5 years or after 10th Katir production.

References

Marasabessy, A. 2014, Analisis Keretakan dan Metode Perawatan yang Tepat Lambung kapal dibawah Garis Air Berbahan Fiberglass, Tesis Magister Teknik ISTN Jakarta

Marassabessy, A. 2009 , ”Disain Kapal Ikan Sederhana Berbahan FRP” , Hasil Penelitian, Bina Widya LPPM UPN “Veteran” Jakarta.

Biro Klasifikasi Indonesia, 1996a. Rules and Regulation for the Classification of Ships (Fibreglass Reinforced Plastic Ships), Jakarta.

Dauri, R. Kebijakan Penerbitan Ijin Kapal Asing di Perairan Zona Ekonomi Eklusif (ZEE), Seminar Nasional,20 Oktober 2001, Penyelenggara HIMASEPA IPB, Jakarta, 9 halaman.

Harbrian, V. 2007.”Pengaruh ketebalan inti (Core) terhadap kekuatan bending komposit sandwich serat E-glass Chopped Strand Mat-Unsaturated Polyester Resin dengan Inti (Core) Spon”, Universitas Negeri Semarang, Semarang

Johan, S. 2011, “Studi Kelayakan Pengembangan Bisnis”, ed.1, Graha Ilmu, Yogyakarta.

Kasmir, J. 2012, Studi Kelayakan Bisnis” ed.Rev.cetakan 8, Kencana, Jakarta.

Nurcahyadi, M. 2010, Tekno ekonomi pembuatan perahu fiberglass di Desa Cikahuripan Kecamatan Cisolok, Sukabumi, Skripsi, Fakultas Perikanan dan Ilmu Kelautan IPB, Bogor.

Soekarsono. 2002, Fishing Vessel, FakultasTeknologi Kelautan, Universitas Darma Persada, Jakarta.

Sukirno, S. 2005, “Mikro Ekonomi Teori Pengantar”. Rajawali Press Universitas Indonesia, LPFE-UI, Jakarta.

Sastrodiwongso, T. 2002, Kemudi dan Olah Gerak Kapal, Fakultas Teknologi Kelautan, Universitas Darma Persada, Jakarta.

Cisanggarung Putra Mandiri CV, 2010, Galangan kapal Fiberglass,. Laporan hasil perawatan kapal fiberglass.

Downloads

Published

2017-12-20

Issue

Vol. 13 No. 2 (2017): Bina Teknika

Section

Articles

License

Journal Bina Teknika grants open acces to all of its content, based on that matter makes all research papers published are freely available to public which ensures greater global excchange of knowledge

  Creative Commons License

Journal Bina Teknika is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Refers to these license, all research papers agree to the following terms:

  • Attribution - Authors holds the credit of their research works published, in order to use materials from one or more research papers published in Bina Teknika should be given appropriate credit
  • Non Commercial - All research papers published in Bina Teknika may not use for commercial purposes
  • Share Alike - Any creation made under one or more concepts from research papers published in Bina Teknika should be distribute your contributions under the same license as original