Pembuatan Batubata dengan Bahan Baku Lumpur Sidoarjo

Authors

  • Endang Srihari Mochni UNIVERSITAS SURABAYA
  • Arief Budhyantoro

DOI:

https://doi.org/10.54378/bt.v17i1.2570

Keywords:

bricks, Sidoarjo mud, paper sludge

Abstract

Many attempts to reduce the volume of Sidoarjo mudflow that came out, one of which is the use of Sidoarjo mud for making bricks. The results of research in the chemical laboratory show that the Sidoarjo mud mineral content is mostly silica and alumina minerals, so it is very supportive for use as a material for making bricks. Making bricks requires mixed materials, one of which is paper sludge. Paper sludge waste is discharged from the paper industry, which can pollute the environment if it is discharged directly into the environment. Therefore, a solution is needed by utilizing the potential of the sludge waste. One of them is by using paper sludge as an additive in making bricks, because most of the components of paper sludge waste are calcium carbonate. In building materials, calcium carbonate can function as an additive so that paper sludge waste can be used as an additional material in making bricks. The purpose of this study is to determine the best ratio of Sidoarjo mud with paper sludge to the quality of the bricks, find out the best combustion temperature to the quality of the bricks produced, and compare the quality of the bricks before and after burning. The bricks are synthesized with a variation of the ratio of Sidoarjo mud raw material and paper sludge (1: 0, 1: 1, 2: 1, 3: 1) and variations in combustion temperature (no combustion, 400°C, 450°C, 500°C, 750°C, 900°C). In this study, the best quality of bricks according to SNI is 2: 1 ratio bricks with a combustion temperature of 750 ° C. The ratio of 2: 1 brick with a combustion temperature of 750°C has a percentage of water absorption of 17.17% and compressive strength of 37.78 kg / cm2.

References

Adonaranita, Florentika dan Mas Suryanto, (2011), “Pengaruh Komposisi Lumpur Lapindo Sidoarjo Terhadap Mutu Batu Bata Berdasarkan SNI 15-2094-2000”, Jurusan Teknik Sipil Universitas Negeri Surabaya, 1-7.

Afrianti, Suci dkk, (2019), “Pengaruh Suhu Pembakaran dan Konsentrasi Grafena Terhadap Karakteristik Batu Bata”, Jom FTEKNIK, 6.

Badan Standarisasi Nasional, ICS 91.100.20 : SNI-15-2094-2000.

Bishop, J., Madejova, J., Komadel, P., Froschl, H., (2002), “The influence of structural Fe, Al and Mg on the infrared OH bands in spectra of dioctahedral smectites”, Clay Miner, 37, 607- 616.

Elika, Elmaghfira Putri dkk, (2017), “Bencana Sosial Kasus Lumpur PT. LAPINDO Brantas

Sidoarjo”, Jurnal Penelitian & PKM, 4, 2, 205-206.

Feya, Oleg D., (2018), “Tetrahedral Honeycomb Surface Reconstructions of Quartz, Cristobalite and Stishovite” Scientific Reports, 8.

Flanigen, E.M., Khatami, H and Szymanski,H, 1971, Infrared Structural Studies of Zeolite Framework, Union Carbide Coorp, Linde Division laboratory, New York

Haldar, S. K., & Tišljar, J, (2014), “Basic Mineralogy. Introduction to Mineralogy and Petrology”39–79.

Hardiani, Henggar dan Susi Sugesty, (2009), “Pemanfaatan Limbah Sludge Industri Kertas Sigaret Untuk Bahan Baku Bata Beton”, Balai Besar Pulp dan Kertas, 86-98.

Hendayana, (1994), “Kimia Analitik Instrumen”, IKIP Semarang Press, Semarang.

Karimah, Rofikatul, (2008), “Potensi Lumpur Lapindo Sebagai Bahan Baku Tambahan Pembuatan Batu Bata”, Hasil Penelitian PBP, 171-125.

Kartika, A., and Darmawan, A, (2008), “Pengaruh Serbuk Kaca dan Variasi Suhu Pembakaran pada Pembuatan Genteng Lempung Sedimentasi Banjir Kanal Timur Kota Semarang terhadap Kuat Tekan serta Daya Serapnya terhadap Air”, Journal of Scientific and Applied Chemistry Journal, 11(3), 63–69.

Madsen FT, Mu¨ller-Vonmoos M, (1989), “The swelling behaviour of clays”, Appl Clay Sci

(2):143–156.

Muhardi, dkk, (2007), “Perbaikan Karakteristik Batu Bata Lempung Dengan Penambahan AbuTerbang”, Jurnal Teknik Sipil, 7, 2.

Mukono dan Triwulan. 2006. Bahan Bangunan dari Lumpur Lapindo Aman bagi Kesehatan.Surabaya: ITS. http://www.its.ac.id/semuaberita.php.

Mustopa, Rendra Syam dan Doty Dewi Risanti, (2013), “Karakterisasi Sifat Fisis Lumpur Panas Sidoarjo dengan Aktivasi Kimia dan Fisika”, Jurnal Teknik POMITS, 2, 2, 256.

Palanivel, R., and Velraj, G, (2007), “FTIR and FT-Raman Spectroscopic Studies of Fired Clay Artifacts Recently Excavated in Tamilnadu”, India Journal of Pure and Applied Physics, 45 (June), 501–508.

Pramono, Susatyo Adi, dkk, (2014), “Sampah Sebagai Bahan Baku Pembuatan Batu Bata”.Semnas Entrepreneurship, 275-294.

Ranjbar, N., Mehrali, M., Mehrali, M., Alengaram, U. J., and Zamin, M, (2015), “Graphene Nanoplatelet- Fly Ash Based Geopolymer Composites”, Cement and Concrete Research Journal, 76, 222–231.

Rosalia, Riezka., Asmi, Dwi,. & Ginting, Ediman Suka, (2016), “Preparasi dan Karakterisasi Keramik Silika (SiO2) Sekam Padi dengan Suhu Kasinasi800°C- 1000°C”, Jurnal Teori dan Aplikasi Fisika, 4, 1.

Siswanto, Budi, (2019), “Perbandingan Nilai Heat Transfer pada Penambahan Material Composit Batu Bata Sebagai Upaya Efisiensi Energy Bangunan Gedung”, JIPTEK, 12, 2.

Wardhana, K. A., & Saepulloh, R. B., (2018), “Pemanfaatan Lumpur Primer Industri Kertas sebagai Absorben”, Jurnal Selulosa, 8, 9-20.

Wiryasa dkk, (2009), “Pemanfaatan Lumpur Lapindo sebagai Bahan Subsitusi Semen dalam Pembuatan Bata Beton Pejal”, Jurnal Ilmiah Teknik Sipil, 12, 39-46.

Yusuf, A dkk, (2011), “Pemanfaatan Limbah Sludge Kertas PT. Adiprima Suraprinta dalam Pembuatan Batako”, Jurnal Aplikasi, 9, 1, 3.

Published

2021-07-22

Issue

Section

Articles