ANALISIS PRODUK PELEK MOTOR TIPE CAST WHEEL BERBAHAN PADUAN ALUMUNIUM
DOI:
https://doi.org/10.54378/bt.v16i2.2306Keywords:
cast wheel rim, impact, stress, finite element methodAbstract
Motorcycle rim is a very important component in vehicles where motorcycle rim is a component that is directly confused with the highway. In the aspect of safety rim is also very important and very calculated in the manufacturing process, the use of high-quality raw materials is very necessary in the manufacture of motorcycle rims. Nowadays, cast wheel rims are very popular among consumers because cast wheel rims have a sportier design compared to spokes. In this research, the design of cast wheels with spoke wheels numbered 5 and 6 with a given impact speed variation of 10km/h, 15km/h and 20km/h. then the rim material used uses aluminum alloy 6061-T6 and the projectile material uses aluminum alloy 6061-T0. The rim that is designed has a diameter of 433.3 mm and a width of 68 mm to make it easier to design a cast wheel rim using software based on the finite element method, by using this software we can design or design a material so that we can know the stress and strain that occurs when simulating an impact on the inter-spoke plane
References
Akbar, NM. (2017) Simulasi Pengujian Impact Drop Test Berdasarkan Standarisasi SNI dan Analisa Perubahan Desain Pelek Mobil Penumpang Dengan Metode Elemen Hingga, Surabaya: Program Studi Teknik Mesin.
Ansys, Inc. (2009) Ansys workbench user’s guide, southpointe 275 technology drive Canonsburg, PA 151317, http:/www.ansys.com
Departemen Perindustrian, Badan Standar Nasional Indonesia (2008) Pelek Kendaraan Bermotor Kategori Lx. Jakarta
Dieter George E. (1987). Metalurgi Mekanik (Edisi Ketiga). (Jilid 2). Jakarta: Erlangga.
E. Madenci, I. Guven, (2015) The Finite Element Method and Applications in Engineering Using ANSYS ®
Giesecke, Frederick E. (2001) Gambar Teknik. Jakarta: Eerlangs
Handoyo, Y. (2003) Perancangan Alat Uji Impact Metode Charpy Kapasitas 100 Joule. Jurnal Ilmiah, Bekasi: Program Studi Teknik Mesin, Universitas Islam.
Imron, M. (2010) Kajian Ketahanan Kejut (impact) Beton Kertas Pada Varian Campuran. Laporan Tugas Akhir, Surakarta: Program Studi Teknik Sipil, Universitas Sebelas Maret.
Irawan, AH, Majanasastra, RBS., Rahmanto, RH. (2016) Analisis Kekuatan Velg Cast Wheel Sepeda Motor Dengan Perangkat Lunak Berbasis Metode Elemen Hingga. Jurnal Ilmiah, Bekasi: Program Studi Teknik Mesin, Universitas Islam.
J.P.Den Hartog (1952) Advanced Strength of Materials. New York: McGraw-Hill Book Company.
Kosasih, PB. (2012) Teori dan Aplikasi Metode Elemen Hingga. Yogyakarta: Andi Publisher
Nugraha, MA. (2019) Analisi Numerik Kekuatan Velg Sepeda Motor Yang Dibebani Dengan Beban Impact, Medan: Program Studi Teknik Mesin.
Prabowo, SA. (2010) Easy to Use Solidworks 2009. Yogyakarta: Andi Publisher
Sutikno S, Raharjo PA. (2003) Metode Elemen Hingga untuk Penyelesaian Persamaan Aliran Turbulen. Jurnal Natur Indonesia.
Wahyudi, A. (2013) Pemeliharaan Sasis Sepeda Motor. Kementrian Pendidikan & Kebudayaan.
Downloads
Published
Issue
Section
License
Journal Bina Teknika grants open acces to all of its content, based on that matter makes all research papers published are freely available to public which ensures greater global excchange of knowledge
Journal Bina Teknika is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
Refers to these license, all research papers agree to the following terms:
- Attribution - Authors holds the credit of their research works published, in order to use materials from one or more research papers published in Bina Teknika should be given appropriate credit
- Non Commercial - All research papers published in Bina Teknika may not use for commercial purposes
- Share Alike - Any creation made under one or more concepts from research papers published in Bina Teknika should be distribute your contributions under the same license as original
