INVESTIGASI KARAKTERISTIK HAMBATAN PENTAMARAN BENTUK LAMBUNG WIGLEY DAN CHINE DENGAN MENGGUNAKAN CFD

Authors

  • Wiwin Sulistyawati Prodi Teknik Perkapalan, Universitas Pembangunan Nasional “Veteran” Jakarta, Jakarta Selatan, Indonesia

DOI:

https://doi.org/10.54378/bt.v13i1.26

Keywords:

pentamaran, deadrise angles, resistance, CFD.

Abstract

Several studies of multi-hulls ship showed that hull resistance could be predicted from position between the each hull. The design optimization of the hull form could be considered by minimizing resistance, which is generally the sum of the viscous resistance and the wave making resistance of the ship model. This paper presents an investigation of pentamaran hull form with chine hull form to the effects of outriggers position, asymmetry, and deadrise angles on the resistance characteristics. This research investigated the resistance characteristics by modeling pentamaran hull form using chine with symmetrical main hull and asymmetric outboard on the variation deadrise angles: 25o, 30o, 35o and Froude number 0,1 to 0,7. We examined the calm water resistance characteristics of six pentamaran models with chine-hull form by variation of deadrise angles using Ansys CFD. Increasing the deadrise angle of chine hull form contribute to the resistance due to the interaction of the wave systems produced by each demihull. Strong interaction effect on the resistance coefficient component was found for change in the hull length as well. Compared to the wigley hull form, the maximum drag reduction of the chine hull form was reduced by 18.05% in deadrise 250, 16.1% in deadrise 300, and 18.19% in deadrise 350. While the smallest value of total resistance coefficient was generated from chine 350 at R/L:1/14 and R/L:1/7. Optimum hull form for minimum resistance has been obtained, so it is interesting to continue with angle of entrance and stem angle of hull for further research.

References

Bari, Ghazi S, and Konstantin I Matveev, (2016), Hydrodynamic modeling of planing catamarans with symmetric hulls. Ocean Engineering 115:60-66.

------------------------------

Begovic, E, and C Bertorello, (2012), Resistance assessment of warped hull form. Ocean Engineering 56:28-42.

----------------------------

Blazek J. 2001. Computational Fluid Dynamics: Principles and Applications. Elsevier Science Ltd, Oxford England.

----------------------------

Blount, Donald L, (1995), Factors Influencing the Selection of a Hard Chine or Round-Bilge Hull for High Froude Numbers

-----------------------------

Chengyi, Wang, (1994), Resistance charicteristic of high-speed catamaran and its application. Shipbuilding of China 3:003

--------------------------------------------

Hsiung. C.C. and Xu. H, (1988), Determining Optimal Forms of a Catamaran for Minimum Resistance by the Mat hematical Programming Met hodo'. Schiffstechnik Bd.35.

----------------------------------------------

Ikeda, Yoshiho, Emiko Nakabayashi, and Ai Ito, (2005), Concept design of a pentamaran type fast RoRo ship. Journal of the Japan Society of Naval Architects and Ocean Engineers 1:35-42.

--------------------------------------------

Michell, J.H., (1898), The Wave-Resistance of a Ship, Philosophical Magazine, Series 5.Vol. 45, Xo. 272, London, January, pp. 105-1 23.

-------------------------------------------

Moraes, HB, JM Vasconcellos, and RG Latorre, (2004), Wave resistance for high-speed catamarans. Ocean Engineering 31(17):2253-2282.

------------------------------------------

Oller, Erik, Vasilios Nikou, and Konstantinos Psallidas, (2003), Focused Mission High Speed Combatant. DTIC Document.

------------------------------------------

Peng, Hongxuan, (2001), Numerical computation of multi-hull ship resistance and motion, Dalhousie University Halifax.

Recommended Procedure and Guidelines, (2002), Testing and Extrapolation Methods in Resistance Towing Tank Tests, ITTC 7.5-02-02-02.

---------------------------------------------

Yanuar, Gunawan, Kurniawan T. Waskito, and A. Jamaluddin, 2015. Experimental Study Resistances of Asymmetrical Pentamaran Model with Separation and Staggered Hull Variation of Inner Side-Hulls, International Journal of Fluid Mechanics Research, Vol. 42, No. 1.

Published

2017-08-02