ANALISA PENGARUH SUHU DAN WAKTU PEMANASAN PADA NYLON FILM TERHADAP MAMPU BENTUK ZIPPER

Authors

  • Mohamad Faizal Program Studi Teknik Mesin Institut Sains Teknologi Nasional ISTN
  • Fahmi Wahyudi Program Studi Teknik Mesin Institut Sains Teknologi Nasional ISTN

DOI:

https://doi.org/10.54378/bt.v13i1.18

Keywords:

Ultrasonic Welding, Zipper, Nylon film, Heating time

Abstract

Ultrasonic Welding has been used to join the thermoplastic material of about 35 years. Now, Ultrasonic Welding has been widely used not only for the thermoplastic material, but also can be used for all kinds of industries, one of which is the textile industry. Ultrasonic Welding has many advantages economically and efficiency. In its use of the zipper industry, Ultrasonic Welding used to join between components to the surface of the film nylon zipper. However, the wrong calculation of the temperature and the length of time could caused the strength of nylon films was reduced to cause permanent damage. This study aims to determine the temperature and duration of heating time. Ultrasonic Welding is used Branson type with power supply 40 kHz / 60 W with a maximum current of 3A. Booster type used is standard series M8 x 1:25 Horn 40 kHz with titanium material. Converter used CH30 with a maximum continuous use at 60 W. attachment method used is butt joint with a gap between the horn surface is ¼ inch zipper.Thermoplastic material in this case used nylon 66.

References

Omer Sahin, Steve Koellhoffer, Suresh Advani “Thermal Modelling During Continuous Ultrasonic Welding”. Turkish Journal of Engineering & Environmental Sciences. 2014.

Emerson. “Polymers: Characteristics and Compatibility for Ultrasonic Assembly”. American Society for Engineering Education, Danbury. 2012.

de Vries, E. Graff K. “Mechanics and Mechanisms of Ultrasonic Welding”. The Ohio State University. 2004.

T.H Hazlett, S. M. Ambekar “Addational Studies on Interface Temperatures and Bonding Mechanisms of Ultrasonic Weld”. Weldng Research Supplement, 1990

Vladimir N, Khmelev, Slivyn, Abramov. "Model of Process and Calculation of Energy for a Heat Generation of a Welded Joint at Ultrasonic Welding Polymeric Thermoplastic Materials". Biysk Technological Institute. Rusia. 2011

Iman Mujiarto. “Sifat dan Karakteristik Material Plastik dan Bahan Aditif”. STMART AMNI , Semarang. 2005

Faten Debbabi. Saber B Abdessalem. “Impact of Hot-stretching Treatment on Physical and Mechanical Properties of Polyamide Suture. Textile Reasearch Journal. 2015.

Downloads

Published

2017-08-02

Issue

Vol. 13 No. 1 (2017): Bina Teknika

Section

Articles

License

Journal Bina Teknika grants open acces to all of its content, based on that matter makes all research papers published are freely available to public which ensures greater global excchange of knowledge

  Creative Commons License

Journal Bina Teknika is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.

Refers to these license, all research papers agree to the following terms:

  • Attribution - Authors holds the credit of their research works published, in order to use materials from one or more research papers published in Bina Teknika should be given appropriate credit
  • Non Commercial - All research papers published in Bina Teknika may not use for commercial purposes
  • Share Alike - Any creation made under one or more concepts from research papers published in Bina Teknika should be distribute your contributions under the same license as original